View RFQ Cart
My Account / RFQ Submission Status
On-line Ballast Calc Form
Vincor™ Field Service
General Feedback Form
Search our site
E-mail existing RFQ
E-mail Vincor™ Sales
Temporary teleport at your facility up to 9.1M
Join our mailing list!
(Your shopping cart is empty)
ETI's ADH NETCOM
Automatic Air Dehydrator with Ethernet Communications
Replaces ADH-2ACOM and ADH-3COM
Available as Rack Mount or Wall Mount!
Vincor™ Product Data and Specification Archives (Adobe® .pdf format)
Documentation via Environmental Technologies, Inc.™
ETI ADH NETCOM Data Sheet
ETI ADH NETCOM AC Installation Data Sheet
ETI ADH NETCOM DC Installation Data Sheet
ETI ADH NETCOM Flow Chart
ETI ADH NETCOM MANUAL
Configure in RFQ Cart
ADH-NETCOM Series Model Selection
ADH NETCOM Automatic Dehydrator, AC [Add $3,914.00]
ADH NETCOM Automatic Dehydrator, AC, w/display [Add $4,175.00]
ADH NETCOM Automatic Dehydrator, DC [Add $4,523.00]
ADH NETCOM Automatic Dehydrator, DC, w/display [Add $4,697.00]
Additional Product Specs
The ADH NETCOM automatic dehydrator supplies low pressure dry air to keep waveguide and coaxial cable dry. Output pressure is configurable between 0.10 psig and 7.50 psig (7mbar - 517mbar) in 0.01 psig (0.67mbar) increments. Factory default pressure is 0.5 psig (34.5mbar). Operational monitoring and alarms are software based making them highly configurable in the field. Future software features can be installed while in service over the internet or local Ethernet network.
Dimensions 17" × 12" × 5-1/4" (432mm × 305mm × 133mm)
Weight 16 lbs (7.26 kg)
Mounting Dual-post rack, flush mounted
Single-post rack, center mounted
Supply 100-240 VAC, 50/60 Hz ±20-75 VDC
Maximum current 1.0 Amps at 100 V
Power usage 40 W typical, 100 W max
Heat dissipation 100 BTU/hr typical, 325 BTU/hr max
Flow rate 25.4 scfh (12 lpm)
Maximum pressure 7.5 psig (517mbar)
Internal safety relief valve 8 psig (552mbar)
Discharge port 1/8" NPT
3/8" or 1/4" hose barb (both included)
Display units SI (millibars); English (psig), default
The ADH NETCOM automatic dehydrator is Ethernet network ready. Units can be configured and monitored using either built in SNMP support or the web interface. Legacy system support is provided via RS-422/485 or RS-232 interfaces. Three programmable alarm relays are also included. Communicated operational information includes output pressure, duty cycle, temperature, compressor hours and air drying canister status.
The ADH NETCOM automatic dehydrator uses a brushless dual-diaphragm pump for long life. Dehydrator operates with exceptionally low noise and vibration levels. The air drying canisters use aluminum oxide desiccant for high efficiency. The humidity sensor signals for regeneration based upon current dew point rather than at fixed time intervals for additional energy savings and long desiccant life.
The ADH NETCOM automatic dehydrator requires only 5-1/4" (3-U) of rack space and is just 12" (304.8mm) deep. Mounting hardware allows for fl exible installation options including dual- and single-post rack mounting and wall mounting. The standard unit weighs just 16 lbs (7.26 kg).
The ADH NETCOM automatic dehydrator operates from 100-240 VAC, 50/60 Hz. Optional units are available at ±20-75 VDC. The dehydrator consumes a maximum of 100 watts during regeneration and approximately 40 watts otherwise. Heat dissipated is up to 325 BTU/hr during regeneration and approximately 100 BTU/hr otherwise. This product creates an exceptionally low heat load for an automatic dehydrator.
Provides dry pressurized air to ensure signal quality of antenna waveguide and dielectric coaxial cable
Highly configurable to meet the needs of wide ranging applications
Programmable operating pressure range: 0.10 psig - 7.50 psig (7mbar - 517mbar)
Brushless compressor for long life
Future-proof software based features allow updates and upgrades while in service
Remote monitoring and control with web interface or SNMP
Configurable Master/Slave operation
Ethernet, RS-422/485, RS-232 and alarm relay outputs for compatibility with nearly any system
Simple power connections for 100-240 VAC or ±20-75 VDC
Small, light weight chassis with multiple mounting options makes installation easy
Low energy use minimizes operational costs
Share your knowledge of this product with other customers...
Be the first to write a review
Browse for more products in the same category as this item:
5652 W. Monee-Manhattan Road
Monee, IL 60449 U.S.A.
Our World Experience Map
Send Us Feedback
Copyright © 2007-2010 Vincor, Ltd.. All Rights Reserved.