View RFQ Cart
My Account / RFQ Submission Status
On-line Ballast Calc Form
Vincor™ Field Service
General Feedback Form
Search our site
E-mail existing RFQ
E-mail Vincor™ Sales
Temporary teleport at your facility up to 9.1M
Join our mailing list!
(Your shopping cart is empty)
ETI's ADH NETCOM Outdoor NEMA
Automatic Air Dehydrator with Ethernet Communications
Replaces ADH-2ACOM and ADH-3COM NEMA
Available for Outdoor & Mobile Applications!
Vincor™ Product Data and Specification Archives (Adobe® .pdf format)
Documentation via Environmental Technologies, Inc.™
ETI ADH NETCOM NEMA Data Sheet
ETI ADH NETCOM NEMA MS Type 1 Data Sheet
ETI ADH NETCOM NEMA MS Type 2 Data Sheet
ETI ADH NETCOM MANUAL
Configure in RFQ Cart
ADH-NETCOM Series Model Selection
ADH NETCOM Automatic Dehydrator, NEMA, AC [Add $4,844.00]Replaces Part# 23483
ADH NETCOM Automatic Dehydrator, NEMA, AC, w/Mil-Spec Conn. Type 1 [Add $5,269.00]Replaces Part# 23740
ADH NETCOM Automatic Dehydrator, NEMA, AC, w/Mil-Spec Conn. Type 2 [Add $5,269.00]Replaces Part# 23856
Additional Product Specs
The ADH NETCOM NEMA automatic dehydrator supplies low pressure dry air to keep waveguide and coaxial cable dry. Output pressure is configurable between 0.10 psig and 7.50 psig (7mbar - 517mbar) in 0.01 psig (0.67mbar) increments. Factory default pressure is 0.5 psig (34.5mbar). Operational monitoring and alarms are software based making them highly configurable in the field. Future software features can be installed while in service over the internet or local Ethernet network.
Dimensions 15.31" × 18.06" × 9.28" (389mm × 459mm × 236mm)
Weight 24 lbs (10.9 kg)
Mounting Wall, post/pole or shelf mounted
Supply 100-240 VAC, 50/60 Hz ±20-75 VDC
Maximum current 1.0 Amps at 100 V
Power usage 200 W max
Heat dissipation 100 BTU/hr typical, 325 BTU/hr max
Flow rate 25.4 scfh (12 lpm)
Maximum pressure 7.5 psig (517mbar)
Internal safety relief valve 8 psig (552mbar)
Discharge port 1/8" NPT
3/8" or 1/4" hose barb (both included)
Display units SI (millibars); English (psig), default
The ADH NETCOM automatic dehydrator is Ethernet network ready. Units can be configured and monitored using either built in SNMP support or the web interface. Legacy system support is provided via RS-422/485 or RS-232 interfaces. Three programmable alarm relays are also included. Communicated operational information includes output pressure, duty cycle, temperature, compressor hours and air drying canister status.
The ADH NETCOM automatic dehydrator uses a brushless dual diaphragm pump for long life. Dehydrator operates with exceptionally low noise and vibration levels. The air drying canisters use aluminum oxide desiccant for high effi ciency. The humidity sensor signals for regeneration based upon current dew point rather than at fi xed time intervals for additional energy savings and long desiccant life.
The ADH NETCOM NEMA automatic dehydrator provides the same functionality as a standard ADH NETCOM in an environmentally sheltered IP66, NEMA 4X enclosure. It is ideal for use with mobile satellite antenna installations and for outdoor mounting for pressurization systems localized to the antenna pedestal. This outdoor confi guration is also ideal for use in pressurization systems in remote locations such as along rail lines, pipe lines and at power distribution substations. While the NEMA enclosure keeps out moisture, the temperature control system allows operation down to –40°F (–40°C). The ADH NETCOM NEMA automatic dehydrator weighs just 24 lbs (10.9 kg).
For complete information describing its application, installation and features, please contact Customer Service or check on the web at www.vincor.com
Provides dry pressurized air to ensure signal quality of antenna waveguide and dielectric coaxial cable
Highly configurable to meet the needs of wide ranging applications
Programmable operating pressure range: 0.10 psig - 7.50 psig (7mbar - 517mbar)
Brushless compressor for long life
Future-proof software based features allow updates and upgrades while in service
Remote monitoring and control with web interface or SNMP
Configurable Master/Slave operation
Ethernet, RS-422/485, RS-232 and alarm relay outputs for compatibility with nearly any system
Durable, light weight IP66, NEMA 4X enclosure
Designed to allow minimal fl ex without damaging enclosure
or components for mobile and other high vibration
Optionally available with military style connectors
Low energy use minimizes operational costs
Share your knowledge of this product with other customers...
Be the first to write a review
Browse for more products in the same category as this item:
5652 W. Monee-Manhattan Road
Monee, IL 60449 U.S.A.
Our World Experience Map
Send Us Feedback
Copyright © 2007-2010 Vincor, Ltd.. All Rights Reserved.